Monday, 24 June 2013

Make an ironing board cover

After all of the wonderful comments about the map fabric I bought in Birmingham, I thought I should step to it and replace the cover of our ironing board. Turns out the language on the fabric is German, amazing what you don't notice when you're so caught up with a fabric!

New Ironing Board cover

Our ironing board is HUGE and was in desperate need of a makeover. You can see the discolouration below which had seeped through to the polyurethane pad. I suspect this caused the discolouring as moisture can't escape through a non-natural fibre. I also had a feeling that one of the layers below the cover had split, or melted, and I was right, there was a rather large hole in the foam layer where it had tried to fuse itself to the metal frame. 

Old yucky ironing board cover

So why make my own? "It's only an ironing board cover!" I hear you say. But I have to look at that cover a lot when I'm sewing. Every now and then I would look for new covers and decide that all of them were not what I wanted. The range of offer was appalling in places! Turns out is rather simple to make your own.

What you need:
Cotton fabric as your top layer
Cotton muslin or similar (I used a cotton sheet)
100% cotton batting
Bias tape, enough to go around your fabric
String or elastic

Make sure that you have 100% cotton materials otherwise you won't be able to use the highest heat on your iron. I haven't supplied quantities as each ironing board is different. Measure the board's length and widest part, then add 7cm or so for each side to allow for the extra fabric hiding under the board. 

Step one
You need to create a pattern for your cover. Remove your current cover and see if there is a polyurethane pad included. If so, pin that to your fabric and add an extra 7cm before cutting. Do this for the cover, the muslin and batting. 

Using old cover as pattern guide

Step two
Create a sandwich with your layers in the following order, from bottom to top: muslin, batting, cover. Baste into place. If you have ever made a quilt you can understand that this is the most time consuming part as you ensure you don't get any creases or bumps!

Cover sandwich

Step three
Create your bias tape, if making your own. Open the tape and pin one edge to the raw edge of your sandwiched cover. Begin at the end where your elastic/string pulls tight. Machine sew all the way round. 

Stitching bias tape

Step four
Fold over the bias tape and stitch along the line you have just sewn, this will create a case for your string or elastic. Ensure that you leave a gap to insert the string/elastic. 

Bias tape gap

Step five
Using a safety pin, thread your elastic/string all the way round. Another way to do this, if you're feeling brave and using string (elastic tends to be too wide) is to encase the string as you pin the tape but be careful not to get it caught in the stitches. Remove your basting stitches.

Step six
Put your new cover onto your ironing board and pull the elastic/string until the cover is taught. Tie off with a knot/bow. 

Placing cover on board

Viola! You have a new ironing board cover. 


New ironing board cover - finished

And yes, I'm still very pleased that I went for the maps! 

6 comments:

  1. Thanks for this Claire! I really need to do this. Outlr current cover is so discoloured, it's awful!

    ReplyDelete
    Replies
    1. Glad it is of help. It feels so much better using a board with a nice cover!

      Delete
  2. It looks brilliant! Plus making your own you don't have any worries over it being too big/ small when you get it home

    ReplyDelete
    Replies
    1. You're so right - I hadn't thought about that!

      Delete
  3. Thanks for this, I have been looking at my sorry looking ironing board and thinking I need to replace the cover. The fabric is lovely.

    ReplyDelete
    Replies
    1. I did that too - it took me about a year to actually do something about it!

      Delete

Do you have thoughts about this post? If so, please leave a comment - I really appreciate them! I read them all and try to reply as much as possible.

LinkWithin

Related Posts Plugin for WordPress, Blogger...